PPorter25.03.2017#1
Приветствую.
Достался NAS Synology DS411slim. Истории его не знаю...
При подаче питания часто моргает синим индикатором питания, ни на что не реагирует, по сети не доступен (Втч родной тулой по МАС-у).
Осмотр выявил, что паяна U20 ( 25P32V6P ) и подпаивались на JP1 (терминал).
Также, замечена дыра в U16 (DC-DC ZT7184). U16 питает проц Marvell 88F6282 ARM. Спецификации на него не нашел... Из даташита ШИМа высчитал, что на выходе 1 В.
Подаю общее питание и питание на проц (от ЛБП), ток 0,70 - 0,85А Что в разумных пределах.
Поменял ШИМку. Другие питания подозрений не вызывают, ничего не перегревается. Поведение меняется:
- часто моргает синим индикатором питания,
- светятся желтым индикаторы всех ХДД 20 секунд и гаснут (не зависимо от наличия ХДД),
- Индикатор сети говорит об некой периодичной активности на ней.
Но NAS не видится в сети (втч родной тулой с детекцией по МАС-у), на кнопки не реагирует.
Цепляюсь к терминалу, логи будут ниже (без ХДД). Из него ясно, что девайс скорее живой чем мёртвый. Непонятно только с доступом по сети.
Настораживает строчка лога :
cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file[ 9.900000] eth0: mac address changed or directory
Думал на подбитую сетевую, сеть Марвел 88e1116r. Чип не калится, нискоомники по входу порта целы.
Поменял сетевую - поведение не меняется....
Теперь логи. Загрузка без ХДД и отключён езернет кабель:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Aug 9 2010 - 19:58:12) Marvell version: 3.5.3
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4
Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
[4096kB@f8000000] Flash: 4 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Synology Model: DS411slim
Fan Status: Good
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Image Name: Linux-2.6.32.12
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1552152 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Image Name: synology_88f6282_411slim 8451
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1030907 Bytes = 1006.7 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #8451 Wed Aug 17 05:12:01 CST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Synology 6282 board
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 24
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411slimv10 ihd_num=0 netif_num=1
[ 0.000000] Synology Hardware Version: DS411slimv10-j
[ 0.000000] Internal HD num: 0
[ 0.000000] Internal netif num: 1
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 244992KB available (3652K code, 519K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1490.94 BogoMIPS (lpj=7454720)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] devtmpfs: initialized
[ 0.240000] xor: measuring software checksum speed
[ 0.290000] arm4regs : 1358.000 MB/sec
[ 0.340000] 8regs : 814.800 MB/sec
[ 0.390000] 32regs : 1051.600 MB/sec
[ 0.390000] xor: using function: arm4regs (1358.000 MB/sec)
[ 0.390000] NET: Registered protocol family 16
[ 0.390000] Feroceon L2: Enabling L2
[ 0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.410000]
[ 0.410000] CPU Interface
[ 0.410000] -------------
[ 0.410000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.410000] SDRAM_CS1 ....disable
[ 0.410000] SDRAM_CS2 ....disable
[ 0.410000] SDRAM_CS3 ....disable
[ 0.410000] PEX0_MEM ....base e0000000, size 128MB
[ 0.410000] PEX0_IO ....base f2000000, size 1MB
[ 0.410000] PEX1_MEM ....base e8000000, size 128MB
[ 0.410000] PEX1_IO ....base f2100000, size 1MB
[ 0.410000] INTER_REGS ....base f1000000, size 1MB
[ 0.410000] NFLASH_CS ....base fa000000, size 2MB
[ 0.410000] SPI_CS ....base f4000000, size 16MB
[ 0.410000] BOOT_ROM_CS ....no such
[ 0.410000] DEV_BOOTCS ....no such
[ 0.410000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.410000] Detected Tclk 200000000 and SysClk 500000000
[ 0.410000] Synology 6282 DS411slim GPIO Init
[ 0.410000] PCIe link is enable, apply PCIe workaround
[ 0.910000] PEX0 interface detected Link X4
[ 1.410000] PEX1 interface detected no Link.
[ 1.410000] PCI: bus0: Fast back to back transfers disabled
[ 1.410000] PCI: bus1: Fast back to back transfers enabled
[ 1.420000] bio: create slab <bio-0> at 0
[ 1.420000] vgaarb: loaded
[ 1.420000] SCSI subsystem initialized
[ 1.590000] raid6: int32x1 118 MB/s
[ 1.760000] raid6: int32x2 173 MB/s
[ 1.930000] raid6: int32x4 169 MB/s
[ 2.100000] raid6: int32x8 181 MB/s
[ 2.100000] raid6: using algorithm int32x8 (181 MB/s)
[ 2.100000] Switching to clocksource kw_clocksource
[ 2.100000] NET: Registered protocol family 2
[ 2.100000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.100000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.100000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.100000] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.100000] TCP reno registered
[ 2.100000] NET: Registered protocol family 1
[ 2.100000] RPC: Registered udp transport module.
[ 2.100000] RPC: Registered tcp transport module.
[ 2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.100000] Trying to unpack rootfs image as initramfs...
[ 3.150000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 3.160000] Freeing initrd memory: 4096K
[ 3.170000] XOR registered 4 channels
[ 3.170000] XOR 2nd invalidate WA enabled
[ 3.170000] VFS: Disk quotas dquot_6.5.2
[ 3.170000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.170000] msgmni has been set to 486
[ 3.170000] alg: No test for md5 (md5-generic)
[ 3.170000] alg: No test for des (des-generic)
[ 3.170000] alg: No test for des3_ede (des3_ede-generic)
[ 3.170000] alg: No test for stdrng (krng)
[ 3.170000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 3.170000] io scheduler noop registered
[ 3.170000] io scheduler anticipatory registered (default)
[ 3.180000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.180000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 3.190000] console [ttyS0] enabled
[ 3.190000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 3.210000] brd: module loaded
[ 3.210000] sata_mv 0000:00:01.0: version 1.28
[ 3.210000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 3.220000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 3.230000] scsi0 : sata_mv
[ 3.230000] scsi1 : sata_mv
[ 3.230000] scsi2 : sata_mv
[ 3.240000] scsi3 : sata_mv
[ 3.240000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[ 3.250000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[ 3.260000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[ 3.260000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[ 3.270000] Enable Synology sata fast booting
[ 4.680000] sata_mv sata_mv.0: version 1.28
[ 4.680000] sata_mv sata_mv.0: slots 32 ports 2
[ 4.690000] scsi4 : sata_mv
[ 4.690000] scsi5 : sata_mv
[ 4.690000] ata5: SATA max UDMA/133 irq 21
[ 4.700000] ata6: SATA max UDMA/133 irq 21
[ 4.700000] Enable Synology sata fast booting
[ 5.040000] ata1: SATA link down (SStatus 0 SControl 300)
[ 5.390000] ata2: SATA link down (SStatus 0 SControl 300)
[ 5.400000] physmap platform flash device: 00400000 at f8000000
[ 5.400000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 5.410000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[ 5.430000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 5.440000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 5.450000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 5.450000] 0x000000000000-0x000000080000 : "RedBoot"
[ 5.460000] 0x000000080000-0x000000280000 : "zImage"
[ 5.460000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 5.470000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 5.470000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.480000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.490000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.490000] serial number='DCH9N00195'
[ 5.490000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 5.500000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 5.510000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[ 5.520000] cmdlinepart partition parsing not available
[ 5.520000] Loading Marvell Ethernet Driver:
[ 5.530000] o Cached descriptors in DRAM
[ 5.530000] o DRAM SW cache-coherency
[ 5.530000] o 2 Giga ports supported
[ 5.540000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 5.540000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 5.550000] o TCP segmentation offload (TSO) supported
[ 5.550000] o Receive checksum offload supported
[ 5.560000] o Transmit checksum offload supported
[ 5.560000] o SKB Recycle supported - (Enabled)
[ 5.570000] o Rx descripors: q0=128
[ 5.570000] o Tx descripors: q0=532
[ 5.580000] o Loading network interface(s):
[ 5.580000] o register under mv88fx_eth platform
[ 5.590000] o eth0, ifindex = 2, GbE port = 0
[ 5.590000] o eth0, phy chipid = 1410e40, Support WOL = 0
[ 5.600000]
[ 5.600000] md: linear personality registered for level -1
[ 5.600000] md: raid0 personality registered for level 0
[ 5.610000] md: raid1 personality registered for level 1
[ 5.620000] md: raid10 personality registered for level 10
[ 5.620000] md: raid6 personality registered for level 6
[ 5.630000] md: raid5 personality registered for level 5
[ 5.630000] md: raid4 personality registered for level 4
[ 5.640000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
[ 5.650000] cpuidle: using governor ladder
[ 5.650000] TCP cubic registered
[ 5.650000] NET: Registered protocol family 17
[ 5.660000] NET: Registered protocol family 15
[ 5.660000] registered taskstats version 1
[ 5.790000] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.790000] ata5: SATA link down (SStatus 0 SControl F300)
[ 6.150000] ata4: SATA link down (SStatus 0 SControl 300)
[ 6.500000] ata6: SATA link down (SStatus 0 SControl F300)
[ 6.500000] md: Waiting for all devices to be available before autodetect
[ 6.510000] md: If you don't use raid, use raid=noautodetect
[ 6.510000] md: Autodetecting RAID arrays.
[ 6.520000] md: Scanned 0 and added 0 devices.
[ 6.520000] md: autorun ...
[ 6.520000] md: ... autorun DONE.
[ 6.530000] RAMDISK: lzma image found at block 0
[ 7.660000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
:: Loading module usbcore[ 7.920000] usbcore: registered new interface driver usbfs
[ 7.930000] usbcore: registered new interface driver hub
[ 7.940000] usbcore: registered new interface driver ethub
[ 7.940000] usbcore: registered new device driver usb
... [ OK ]
:: Loading module ehci-hcd[ 8.020000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.020000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 8.030000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 8.070000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 8.090000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 8.090000] usb usb1: configuration #1 chosen from 1 choice
[ 8.120000] hub 1-0:1.0: USB hub found
[ 8.120000] hub 1-0:1.0: 1 port detected
... [ OK ]
:: Loading module ohci-hcd[ 8.230000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
... [ OK ]
:: Loading module xhci-hcd ... [ OK ]
:: Loading module etxhci-hcd ... [ OK ]
Insert net driver(Mindspeed only)...
[ 8.380000] ds411slim_synobios: module license 'Synology Inc.' taints kernel.
[ 8.390000] Disabling lock debugging due to kernel taint
[ 8.410000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 8.420000] correction with 0x00
[ 8.450000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 8.520000] 2000-256-0 8:26:0 UTC
[ 8.520000] synobios: load, major number 201
[ 8.530000] Brand: Synology
[ 8.530000] Model: DS-411slim
[ 8.530000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 8.540000] synobios cpu_arch proc entry initialized
[ 8.550000] synobios crypto_hw proc entry initialized
[ 8.550000] synobios syno_platform proc entry initialized
[ 8.560000] usb 1-1: new high speed USB device using orion-ehci and address 2
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[ 8.600000] synobios: unload
Exit on error [1] DISK NOT INSTALLED...
Fri May 7 08:26:00 UTC 2021
sys /sys sysfs rw,relatime 0 0
/dev/root.old / ext2 rw,relatime,errors=continue,user_xattr 0 0
none /dev devtmpfs rw,relatime,size=122604k,nr_inodes=30651,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 1
starting pid 573, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [ OK ]
:: Mounting tmpfs ... [ OK ]
:: Mounting devtmpfs ... [ OK ]
:: Mounting devpts ... [ OK ]
:: Mounting sysfs ... [ OK ]
mdadm: error opening /dev/md1: No such file or directory
rc: Use all internal disk as swap.
rc: No internal disk installed.
swapon: can't stat '/dev/md1': No such file or directory
:: Loading module fat ... [ OK ]
:: Loading module vfat ... [ OK ]
:: Mounting usbfs ... [ OK ]
:: Loading module sky2[ 9.450000] sky2 driver version 1.25
... [ OK ]
:: Loading module synobios[ 9.530000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 9.540000] correction with 0x00
[ 9.570000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 9.640000] 2000-256-0 8:26:0 UTC
[ 9.640000] synobios: load, major number 201
[ 9.650000] Brand: Synology
[ 9.650000] Model: DS-411slim
[ 9.650000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 9.660000] synobios cpu_arch proc entry initialized
[ 9.670000] synobios crypto_hw proc entry initialized
[ 9.670000] synobios syno_platform proc entry initialized
... [ OK ]
cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file[ 9.900000] eth0: mac address changed
or directory
[ 11.940000] eth0: started
udhcpc (v1.16.1) started
eth0 Link encap:Ethernet HWaddr 00:50:43:3C:3D:5D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 TX bytes:0 (0.0
Interrupt:11
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 TX bytes:0 (0.0
:: Starting syslogd ... [ OK ]
:: Starting scemd
Без ХДД с подключённым интернетом:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Aug 9 2010 - 19:58:12) Marvell version: 3.5.3
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4
Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
[4096kB@f8000000] Flash: 4 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Synology Model: DS411slim
Fan Status: Good
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Image Name: Linux-2.6.32.12
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1552152 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Image Name: synology_88f6282_411slim 8451
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1030907 Bytes = 1006.7 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #8451 Wed Aug 17 05:12:01 CST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Synology 6282 board
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 24
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411slimv10 ihd_num=0 netif_num=1
[ 0.000000] Synology Hardware Version: DS411slimv10-j
[ 0.000000] Internal HD num: 0
[ 0.000000] Internal netif num: 1
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 244992KB available (3652K code, 519K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1490.94 BogoMIPS (lpj=7454720)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] devtmpfs: initialized
[ 0.240000] xor: measuring software checksum speed
[ 0.290000] arm4regs : 1358.000 MB/sec
[ 0.340000] 8regs : 814.800 MB/sec
[ 0.390000] 32regs : 1051.600 MB/sec
[ 0.390000] xor: using function: arm4regs (1358.000 MB/sec)
[ 0.390000] NET: Registered protocol family 16
[ 0.390000] Feroceon L2: Enabling L2
[ 0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.410000]
[ 0.410000] CPU Interface
[ 0.410000] -------------
[ 0.410000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.410000] SDRAM_CS1 ....disable
[ 0.410000] SDRAM_CS2 ....disable
[ 0.410000] SDRAM_CS3 ....disable
[ 0.410000] PEX0_MEM ....base e0000000, size 128MB
[ 0.410000] PEX0_IO ....base f2000000, size 1MB
[ 0.410000] PEX1_MEM ....base e8000000, size 128MB
[ 0.410000] PEX1_IO ....base f2100000, size 1MB
[ 0.410000] INTER_REGS ....base f1000000, size 1MB
[ 0.410000] NFLASH_CS ....base fa000000, size 2MB
[ 0.410000] SPI_CS ....base f4000000, size 16MB
[ 0.410000] BOOT_ROM_CS ....no such
[ 0.410000] DEV_BOOTCS ....no such
[ 0.410000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.410000] Detected Tclk 200000000 and SysClk 500000000
[ 0.410000] Synology 6282 DS411slim GPIO Init
[ 0.410000] PCIe link is enable, apply PCIe workaround
[ 0.910000] PEX0 interface detected Link X4
[ 1.410000] PEX1 interface detected no Link.
[ 1.410000] PCI: bus0: Fast back to back transfers disabled
[ 1.410000] PCI: bus1: Fast back to back transfers enabled
[ 1.420000] bio: create slab <bio-0> at 0
[ 1.420000] vgaarb: loaded
[ 1.420000] SCSI subsystem initialized
[ 1.590000] raid6: int32x1 118 MB/s
[ 1.760000] raid6: int32x2 173 MB/s
[ 1.930000] raid6: int32x4 169 MB/s
[ 2.100000] raid6: int32x8 181 MB/s
[ 2.100000] raid6: using algorithm int32x8 (181 MB/s)
[ 2.100000] Switching to clocksource kw_clocksource
[ 2.100000] NET: Registered protocol family 2
[ 2.100000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.100000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.100000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.100000] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.100000] TCP reno registered
[ 2.100000] NET: Registered protocol family 1
[ 2.100000] RPC: Registered udp transport module.
[ 2.100000] RPC: Registered tcp transport module.
[ 2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.100000] Trying to unpack rootfs image as initramfs...
[ 3.150000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 3.170000] Freeing initrd memory: 4096K
[ 3.170000] XOR registered 4 channels
[ 3.170000] XOR 2nd invalidate WA enabled
[ 3.170000] VFS: Disk quotas dquot_6.5.2
[ 3.170000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.170000] msgmni has been set to 486
[ 3.170000] alg: No test for md5 (md5-generic)
[ 3.170000] alg: No test for des (des-generic)
[ 3.170000] alg: No test for des3_ede (des3_ede-generic)
[ 3.170000] alg: No test for stdrng (krng)
[ 3.170000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 3.170000] io scheduler noop registered
[ 3.170000] io scheduler anticipatory registered (default)
[ 3.180000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.180000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 3.190000] console [ttyS0] enabled
[ 3.190000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 3.210000] brd: module loaded
[ 3.210000] sata_mv 0000:00:01.0: version 1.28
[ 3.210000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 3.220000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 3.230000] scsi0 : sata_mv
[ 3.230000] scsi1 : sata_mv
[ 3.230000] scsi2 : sata_mv
[ 3.240000] scsi3 : sata_mv
[ 3.240000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[ 3.250000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[ 3.260000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[ 3.260000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[ 3.270000] Enable Synology sata fast booting
[ 4.680000] sata_mv sata_mv.0: version 1.28
[ 4.680000] sata_mv sata_mv.0: slots 32 ports 2
[ 4.690000] scsi4 : sata_mv
[ 4.690000] scsi5 : sata_mv
[ 4.690000] ata5: SATA max UDMA/133 irq 21
[ 4.700000] ata6: SATA max UDMA/133 irq 21
[ 4.700000] Enable Synology sata fast booting
[ 5.040000] ata1: SATA link down (SStatus 0 SControl 300)
[ 5.390000] ata2: SATA link down (SStatus 0 SControl 300)
[ 5.400000] physmap platform flash device: 00400000 at f8000000
[ 5.400000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 5.410000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[ 5.430000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 5.440000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 5.450000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 5.450000] 0x000000000000-0x000000080000 : "RedBoot"
[ 5.460000] 0x000000080000-0x000000280000 : "zImage"
[ 5.460000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 5.470000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 5.470000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.480000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.490000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.490000] serial number='DCH9N00195'
[ 5.490000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 5.500000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 5.510000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[ 5.520000] cmdlinepart partition parsing not available
[ 5.520000] Loading Marvell Ethernet Driver:
[ 5.530000] o Cached descriptors in DRAM
[ 5.530000] o DRAM SW cache-coherency
[ 5.530000] o 2 Giga ports supported
[ 5.540000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 5.540000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 5.550000] o TCP segmentation offload (TSO) supported
[ 5.550000] o Receive checksum offload supported
[ 5.560000] o Transmit checksum offload supported
[ 5.560000] o SKB Recycle supported - (Enabled)
[ 5.570000] o Rx descripors: q0=128
[ 5.570000] o Tx descripors: q0=532
[ 5.580000] o Loading network interface(s):
[ 5.580000] o register under mv88fx_eth platform
[ 5.590000] o eth0, ifindex = 2, GbE port = 0
[ 5.590000] o eth0, phy chipid = 1410e40, Support WOL = 0
[ 5.600000]
[ 5.600000] md: linear personality registered for level -1
[ 5.600000] md: raid0 personality registered for level 0
[ 5.610000] md: raid1 personality registered for level 1
[ 5.620000] md: raid10 personality registered for level 10
[ 5.620000] md: raid6 personality registered for level 6
[ 5.630000] md: raid5 personality registered for level 5
[ 5.630000] md: raid4 personality registered for level 4
[ 5.640000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
[ 5.650000] cpuidle: using governor ladder
[ 5.650000] TCP cubic registered
[ 5.650000] NET: Registered protocol family 17
[ 5.660000] NET: Registered protocol family 15
[ 5.660000] registered taskstats version 1
[ 5.790000] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.790000] ata5: SATA link down (SStatus 0 SControl F300)
[ 6.150000] ata4: SATA link down (SStatus 0 SControl 300)
[ 6.500000] ata6: SATA link down (SStatus 0 SControl F300)
[ 6.500000] md: Waiting for all devices to be available before autodetect
[ 6.510000] md: If you don't use raid, use raid=noautodetect
[ 6.510000] md: Autodetecting RAID arrays.
[ 6.520000] md: Scanned 0 and added 0 devices.
[ 6.520000] md: autorun ...
[ 6.520000] md: ... autorun DONE.
[ 6.530000] RAMDISK: lzma image found at block 0
[ 7.660000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
:: Loading module usbcore[ 7.920000] usbcore: registered new interface driver usbfs
[ 7.920000] usbcore: registered new interface driver hub
[ 7.950000] usbcore: registered new interface driver ethub
[ 7.950000] usbcore: registered new device driver usb
... [ OK ]
:: Loading module ehci-hcd[ 8.020000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.020000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 8.030000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 8.070000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 8.090000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 8.090000] usb usb1: configuration #1 chosen from 1 choice
[ 8.120000] hub 1-0:1.0: USB hub found
[ 8.120000] hub 1-0:1.0: 1 port detected
... [ OK ]
:: Loading module ohci-hcd[ 8.230000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
... [ OK ]
:: Loading module xhci-hcd ... [ OK ]
:: Loading module etxhci-hcd ... [ OK ]
Insert net driver(Mindspeed only)...
[ 8.380000] ds411slim_synobios: module license 'Synology Inc.' taints kernel.
[ 8.390000] Disabling lock debugging due to kernel taint
[ 8.410000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 8.420000] correction with 0x00
[ 8.450000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 8.520000] 2000-256-0 8:30:0 UTC
[ 8.520000] synobios: load, major number 201
[ 8.530000] Brand: Synology
[ 8.530000] Model: DS-411slim
[ 8.530000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 8.540000] synobios cpu_arch proc entry initialized
[ 8.550000] synobios crypto_hw proc entry initialized
[ 8.550000] synobios syno_platform proc entry initialized
[ 8.560000] usb 1-1: new high speed USB device using orion-ehci and address 2
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[ 8.600000] synobios: unload
Exit on error [1] DISK NOT INSTALLED...
Fri May 7 08:30:00 UTC 2021
sys /sys sysfs rw,relatime 0 0
/dev/root.old / ext2 rw,relatime,errors=continue,user_xattr 0 0
none /dev devtmpfs rw,relatime,size=122604k,nr_inodes=30651,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 1
starting pid 573, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [ OK ]
:: Mounting tmpfs ... [ OK ]
:: Mounting devtmpfs ... [ OK ]
:: Mounting devpts ... [ OK ]
:: Mounting sysfs ... [ OK ]
mdadm: error opening /dev/md1: No such file or directory
rc: Use all internal disk as swap.
rc: No internal disk installed.
swapon: can't stat '/dev/md1': No such file or directory
:: Loading module fat ... [ OK ]
:: Loading module vfat ... [ OK ]
:: Mounting usbfs ... [ OK ]
:: Loading module sky2[ 9.450000] sky2 driver version 1.25
... [ OK ]
:: Loading module synobios[ 9.530000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 9.540000] correction with 0x00
[ 9.570000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 9.640000] 2000-256-0 8:30:0 UTC
[ 9.640000] synobios: load, major number 201
[ 9.650000] Brand: Synology
[ 9.650000] Model: DS-411slim
[ 9.650000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 9.660000] synobios cpu_arch proc entry initialized
[ 9.660000] synobios crypto_hw proc entry initialized
[ 9.670000] synobios syno_platform proc entry initialized
... [ OK ]
cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file[ 9.900000] eth0: mac address changed
or directory
[ 12.940000] ethPort_0: TIMEOUT for TX stoped !!! txQueueCmd - 0x08101
[ 12.940000] eth0: link down
[ 12.950000] eth0: started
udhcpc (v1.16.1) started
[ 13.060000] eth0: link up, full duplex, speed 1 Gbps
Мне бросаются в глаза ошибки по отсутствию файлов. В логе с кабелем не отображается МАС, линк видит но на последней строчке лога все виснет (?).
На кнопки не реагирует, не пищит.
Поскольку паялась флеш память, дeмаю может "подбит" дамп (хотя CRC в порядке). Пытаюсь обновить прошивку по ТФТП:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Aug 9 2010 - 19:58:12) Marvell version: 3.5.3
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4
Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
[4096kB@f8000000] Flash: 4 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Synology Model: DS411slim
Fan Status: Good
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Marvell>> printenv
bootcmd=bootm F8080000 F8280000
baudrate=115200
loads_echo=0
ipaddr=192.168.1.154
serverip=192.168.1.155
rootpath=/mnt/ARM_FS/
netmask=255.255.254.0
run_diag=yes
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x300000@0x100000(root)
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
lcd0_bootargs=video-dovefb:lcd0:$(lcd0_params) clcd.lcd0_enable=$(lcd0_enable)
bootdelay=3
disaMvPnp=no
ethaddr=00:50:43:3c:3b:5d
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
pcieTune=no
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411slimv10 ihd_num=0 netif_num=1
ethact=egiga0
Environment size: 1241/4092 bytes
Marvell>> tftpboot
*** Warning: no boot file name; using 'C0A8019A.img'
Using egiga0 device
TFTP from server 192.168.1.155; our IP address is 192.168.1.154
Filename 'C0A8019A.img'.
Load address: 0x800000
Loading: *
Распаковываю прошивку, имидж переименовываю на C0A8019A.img На компе 192.168.1.155, запускаю ТФТП сервер, НАС подключаю кросовым кабелем напрямую к компу.
Сервер клиента (НАСа) не видит, прошивка не грузится...
Из printenv вижу МАС НАСа, он НЕ СОВПАДАЕТ с МАСом на наклеке устройства 
Значит, или у меня левый дамп прошивки или в УБУТа свой МАС.
На всякий случай, еще один лог с полуподбитым ХДД в 4 порту, без подкл. езернета
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Aug 9 2010 - 19:58:12) Marvell version: 3.5.3
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4
Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
[4096kB@f8000000] Flash: 4 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Synology Model: DS411slim
Fan Status: Good
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Image Name: Linux-2.6.32.12
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1552152 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Image Name: synology_88f6282_411slim 8451
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1030907 Bytes = 1006.7 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #8451 Wed Aug 17 05:12:01 CST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Synology 6282 board
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 24
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411slimv10 ihd_num=0 netif_num=1
[ 0.000000] Synology Hardware Version: DS411slimv10-j
[ 0.000000] Internal HD num: 0
[ 0.000000] Internal netif num: 1
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 244992KB available (3652K code, 519K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1490.94 BogoMIPS (lpj=7454720)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] devtmpfs: initialized
[ 0.240000] xor: measuring software checksum speed
[ 0.290000] arm4regs : 1358.000 MB/sec
[ 0.340000] 8regs : 814.800 MB/sec
[ 0.390000] 32regs : 1051.600 MB/sec
[ 0.390000] xor: using function: arm4regs (1358.000 MB/sec)
[ 0.390000] NET: Registered protocol family 16
[ 0.390000] Feroceon L2: Enabling L2
[ 0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.410000]
[ 0.410000] CPU Interface
[ 0.410000] -------------
[ 0.410000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.410000] SDRAM_CS1 ....disable
[ 0.410000] SDRAM_CS2 ....disable
[ 0.410000] SDRAM_CS3 ....disable
[ 0.410000] PEX0_MEM ....base e0000000, size 128MB
[ 0.410000] PEX0_IO ....base f2000000, size 1MB
[ 0.410000] PEX1_MEM ....base e8000000, size 128MB
[ 0.410000] PEX1_IO ....base f2100000, size 1MB
[ 0.410000] INTER_REGS ....base f1000000, size 1MB
[ 0.410000] NFLASH_CS ....base fa000000, size 2MB
[ 0.410000] SPI_CS ....base f4000000, size 16MB
[ 0.410000] BOOT_ROM_CS ....no such
[ 0.410000] DEV_BOOTCS ....no such
[ 0.410000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.410000] Detected Tclk 200000000 and SysClk 500000000
[ 0.410000] Synology 6282 DS411slim GPIO Init
[ 0.410000] PCIe link is enable, apply PCIe workaround
[ 0.910000] PEX0 interface detected Link X4
[ 1.410000] PEX1 interface detected no Link.
[ 1.410000] PCI: bus0: Fast back to back transfers disabled
[ 1.410000] PCI: bus1: Fast back to back transfers enabled
[ 1.420000] bio: create slab <bio-0> at 0
[ 1.420000] vgaarb: loaded
[ 1.420000] SCSI subsystem initialized
[ 1.590000] raid6: int32x1 118 MB/s
[ 1.760000] raid6: int32x2 173 MB/s
[ 1.930000] raid6: int32x4 169 MB/s
[ 2.100000] raid6: int32x8 181 MB/s
[ 2.100000] raid6: using algorithm int32x8 (181 MB/s)
[ 2.100000] Switching to clocksource kw_clocksource
[ 2.100000] NET: Registered protocol family 2
[ 2.100000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.100000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.100000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.100000] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.100000] TCP reno registered
[ 2.100000] NET: Registered protocol family 1
[ 2.100000] RPC: Registered udp transport module.
[ 2.100000] RPC: Registered tcp transport module.
[ 2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.100000] Trying to unpack rootfs image as initramfs...
[ 3.150000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 3.160000] Freeing initrd memory: 4096K
[ 3.170000] XOR registered 4 channels
[ 3.170000] XOR 2nd invalidate WA enabled
[ 3.170000] VFS: Disk quotas dquot_6.5.2
[ 3.170000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.170000] msgmni has been set to 486
[ 3.170000] alg: No test for md5 (md5-generic)
[ 3.170000] alg: No test for des (des-generic)
[ 3.170000] alg: No test for des3_ede (des3_ede-generic)
[ 3.170000] alg: No test for stdrng (krng)
[ 3.170000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 3.170000] io scheduler noop registered
[ 3.170000] io scheduler anticipatory registered (default)
[ 3.180000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.180000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 3.190000] console [ttyS0] enabled
[ 3.190000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 3.210000] brd: module loaded
[ 3.210000] sata_mv 0000:00:01.0: version 1.28
[ 3.210000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 3.220000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 3.230000] scsi0 : sata_mv
[ 3.230000] scsi1 : sata_mv
[ 3.230000] scsi2 : sata_mv
[ 3.240000] scsi3 : sata_mv
[ 3.240000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[ 3.250000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[ 3.260000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[ 3.260000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[ 3.270000] Enable Synology sata fast booting
[ 4.680000] sata_mv sata_mv.0: version 1.28
[ 4.680000] sata_mv sata_mv.0: slots 32 ports 2
[ 4.690000] scsi4 : sata_mv
[ 4.690000] scsi5 : sata_mv
[ 4.690000] ata5: SATA max UDMA/133 irq 21
[ 4.700000] ata6: SATA max UDMA/133 irq 21
[ 4.700000] Enable Synology sata fast booting
[ 5.200000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 5.400000] physmap platform flash device: 00400000 at f8000000
[ 5.400000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 5.410000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[ 5.430000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 5.440000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 5.450000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 5.450000] 0x000000000000-0x000000080000 : "RedBoot"
[ 5.460000] 0x000000080000-0x000000280000 : "zImage"
[ 5.460000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 5.470000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 5.470000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.480000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.490000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 5.490000] serial number='DCH9N00195'
[ 5.500000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 5.500000] ata1.00: ATA-8: WDC WD7500BPVT-24HXZT3, 03.01A03, max UDMA/133
[ 5.510000] ata1.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 5.520000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 5.520000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[ 5.530000] cmdlinepart partition parsing not available
[ 5.540000] Loading Marvell Ethernet Driver:
[ 5.540000] o Cached descriptors in DRAM
[ 5.550000] o DRAM SW cache-coherency
[ 5.550000] o 2 Giga ports supported
[ 5.550000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 5.560000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 5.560000] o TCP segmentation offload (TSO) supported
[ 5.570000] o Receive checksum offload supported
[ 5.570000] o Transmit checksum offload supported
[ 5.580000] o SKB Recycle supported - (Enabled)
[ 5.580000] o Rx descripors: q0=128
[ 5.590000] o Tx descripors: q0=532
[ 5.590000] o Loading network interface(s):
[ 5.600000] o register under mv88fx_eth platform
[ 5.600000] o eth0, ifindex = 2, GbE port = 0
[ 5.610000] o eth0, phy chipid = 1410e40, Support WOL = 0
[ 5.610000]
[ 5.610000] md: linear personality registered for level -1
[ 5.620000] md: raid0 personality registered for level 0
[ 5.620000] md: raid1 personality registered for level 1
[ 5.630000] md: raid10 personality registered for level 10
[ 5.640000] md: raid6 personality registered for level 6
[ 5.640000] md: raid5 personality registered for level 5
[ 5.650000] md: raid4 personality registered for level 4
[ 5.650000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
[ 5.660000] cpuidle: using governor ladder
[ 5.670000] TCP cubic registered
[ 5.670000] NET: Registered protocol family 17
[ 5.670000] NET: Registered protocol family 15
[ 5.680000] ata1.00: configured for UDMA/133
[ 5.680000] registered taskstats version 1
[ 5.700000] scsi 0:0:0:0: Direct-Access WDC WD7500BPVT-24HXZT3 03.0 PQ: 0 ANSI: 5
[ 5.710000] sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
[ 5.710000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 5.720000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.720000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.730000] sda: sda1 sda2
[ 5.750000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.800000] ata5: SATA link down (SStatus 0 SControl F300)
[ 6.060000] ata2: SATA link down (SStatus 0 SControl 300)
[ 6.410000] ata3: SATA link down (SStatus 0 SControl 300)
[ 6.760000] ata4: SATA link down (SStatus 0 SControl 300)
[ 7.110000] ata6: SATA link down (SStatus 0 SControl F300)
[ 7.110000] md: Waiting for all devices to be available before autodetect
[ 7.120000] md: If you don't use raid, use raid=noautodetect
[ 7.120000] md: Autodetecting RAID arrays.
[ 7.130000] md: Scanned 0 and added 0 devices.
[ 7.130000] md: autorun ...
[ 7.130000] md: ... autorun DONE.
[ 7.140000] RAMDISK: lzma image found at block 0
[ 8.270000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
:: Loading module usbcore[ 8.530000] usbcore: registered new interface driver usbfs
[ 8.530000] usbcore: registered new interface driver hub
[ 8.560000] usbcore: registered new interface driver ethub
[ 8.560000] usbcore: registered new device driver usb
... [ OK ]
:: Loading module ehci-hcd[ 8.630000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.630000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 8.640000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 8.680000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 8.700000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 8.700000] usb usb1: configuration #1 chosen from 1 choice
[ 8.730000] hub 1-0:1.0: USB hub found
[ 8.730000] hub 1-0:1.0: 1 port detected
... [ OK ]
:: Loading module ohci-hcd[ 8.840000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
... [ OK ]
:: Loading module xhci-hcd ... [ OK ]
:: Loading module etxhci-hcd ... [ OK ]
Insert net driver(Mindspeed only)...
[ 8.990000] ds411slim_synobios: module license 'Synology Inc.' taints kernel.
[ 9.000000] Disabling lock debugging due to kernel taint
[ 9.020000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 9.030000] correction with 0x00
[ 9.070000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[ 9.130000] 2000-256-0 8:43:0 UTC
[ 9.130000] synobios: load, major number 201
[ 9.140000] Brand: Synology
[ 9.140000] Model: DS-411slim
[ 9.140000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 9.150000] synobios cpu_arch proc entry initialized
[ 9.160000] synobios crypto_hw proc entry initialized
[ 9.160000] synobios syno_platform proc entry initialized
[ 9.170000] usb 1-1: new high speed USB device using orion-ehci and address 2
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[ 9.210000] synobios: unload
Partition Version=0
Partition layout is not DiskStation style.
NOT EXECUTE /sbin/e2fsck.
Mounting /dev/md0 /tmpRoot
mount: lseek failed, msg:Invalid argument
mount: mounting /dev/md0 on /tmpRoot failed: No such device
mount /dev/md0 fail, returns
Exit on error [3] no init exists...
Fri May 7 08:43:00 UTC 2021
sys /sys sysfs rw,relatime 0 0
/dev/root.old / ext2 rw,relatime,errors=continue,user_xattr 0 0
none /dev devtmpfs rw,relatime,size=122604k,nr_inodes=30651,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 3
starting pid 595, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [ OK ]
:: Mounting tmpfs ... [ OK ]
:: Mounting devtmpfs ... [ OK ]
:: Mounting devpts ... [ OK ]
:: Mounting sysfs ... [ OK ]
mdadm: error opening /dev/md1: No such file or directory
rc: Use all internal disk as swap.
/etc/rc: line 107: sed: not found
/etc/rc: line 107: /usr/syno/sbin/synostgsysraid: not found
[ 9.540000] ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 9.550000] ata1.00: edma_err_cause=00000280 pp_flags=00000003, parity error, EDMA self-disable
[ 9.560000] ata1.00: failed command: READ FPDMA QUEUED
[ 9.560000] ata1.00: cmd 60/20:00:00:38:cd/00:00:17:00:00/40 tag 0 ncq 16384 in
[ 9.560000] res 40/00:ff:ff:ff:ff/00:ff:ff:ff:ff/ff Emask 0x10 (ATA bus error)
[ 9.570000] ata1.00: status: { DRDY }
[ 9.570000] ata1: hard resetting link
[ 10.090000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 10.190000] ata1.00: configured for UDMA/133
[ 10.190000] ata1: EH complete
[ 10.210000] ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 10.210000] ata1.00: edma_err_cause=00000280 pp_flags=00000003, parity error, EDMA self-disable
[ 10.220000] ata1.00: failed command: READ FPDMA QUEUED
[ 10.230000] ata1.00: cmd 60/20:00:00:38:cd/00:00:17:00:00/40 tag 0 ncq 16384 in
[ 10.230000] res 50/00:ff:ff:ff:ff/00:ff:ff:ff:ff/ff Emask 0x10 (ATA bus error)
[ 10.240000] ata1.00: status: { DRDY }
[ 10.250000] ata1: hard resetting link
[ 10.760000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 10.860000] ata1.00: configured for UDMA/133
[ 10.860000] ata1: EH complete
[ 10.880000] ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 10.880000] ata1.00: edma_err_cause=00000280 pp_flags=00000003, parity error, EDMA self-disable
[ 10.890000] ata1.00: failed command: READ FPDMA QUEUED
[ 10.900000] ata1.00: cmd 60/20:00:00:38:cd/00:00:17:00:00/40 tag 0 ncq 16384 in
[ 10.900000] res 50/00:ff:ff:ff:ff/00:ff:ff:ff:ff/ff Emask 0x10 (ATA bus error)
[ 10.910000] ata1.00: status: { DRDY }
[ 10.920000] ata1: hard resetting link
[ 11.430000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 11.530000] ata1.00: configured for UDMA/133
[ 11.530000] ata1: EH complete
[ 11.540000] ata1: limiting SATA link speed to 1.5 Gbps
[ 11.540000] ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 11.550000] ata1.00: edma_err_cause=00000280 pp_flags=00000003, parity error, EDMA self-disable
[ 11.560000] ata1.00: failed command: READ FPDMA QUEUED
[ 11.560000] ata1.00: cmd 60/20:00:00:38:cd/00:00:17:00:00/40 tag 0 ncq 16384 in
[ 11.560000] res 50/00:ff:ff:ff:ff/00:ff:ff:ff:ff/ff Emask 0x10 (ATA bus error)
[ 11.570000] ata1.00: status: { DRDY }
[ 11.570000] ata1: hard resetting link
Все логи полные, тоесть дальше висит.
Оп безысходности пропаял проц, РАМ, рейд контроллер, поменял GST5009LF - поведение не поменялось
Поскольку по железу уже всё перерыто, помогите разобраться с софтовыми нюансами.
Помогите проанализировать логи и понять, что не хватает девайсу.
В идеале, мне нужен родной дамп прошивки (U20 M25P32). Свой я вычитал на внешнем программаторе (4мб.) может кто имеет возможность его проверить или пофиксить?
Потратил много времени на устройство, жаль выбрасывать. Осталось чуть чуть 
до нормальной работы
Исходные данные по девайсу.:
Synology DS411slim (S/N. DCH9N00195 MAC:0011322A0DA7
плата ADM41L1 Ver 1.3 (P/N 08-06ADM4113) + наклейка "1922".
Инфа из УБУТа:
Marvell>> version U-Boot 1.1.4 (Aug 9 2010 - 19:58:12) Marvell version: 3.5.3
Допускаю, что в устройство залит не родной дамп (например, от другой ревизии железа). Ткните носом как проверить и где взять РОДНОЙ ДАМП прошивки U20 (ST M25P32).
Писал в английский сапорт- пришла отписка типа "перезапустить, подёргать кабель"
На Вас, официалов, и этот форум последняя надежда...